Follow the procedure as outlined below using CD37 or higher to perform retrofit coding:
The retrofit coding procedure now works properly with the release of DIS CD38 or higher.
Install the eject box as per the installation instructions.
1. Start CIP (make sure CIP 12.0 or higher is being used).
2. Select "Load Software".
3. At the "Status Report", select "Cancel Update".
4. Select "Retrofits" button at lower right hand corner.
5. Select "Retrofits".
6. Select "Telephone".
7. Select "Telephone Added".
8. When the "Measures Plan" is displayed, select "Accept" and start programming/coding. It is very that the
TCU be programmed even though the Measures Plan indicates the same programmed number before and after
programming.
important
9. The Final Report should state, "Retrofit, telephone, Added" and also show the programming and coding of the TCU
as successful. Check for the proper coding of the TCU by placing a test call to the BMW Assist Response Center.
Push the "SOS" button in the overhead console with the vehicle parked outside, the engine running, and the map CD
installed. When the service representative answers, clarify that the call is a dealer test call, and then request the VIN
number. Write down the VIN number and verify that it matches the vehicle's VIN. If the numbers don't match, the
coding procedure was not successful and needs to be repeated. Note that the handset does not need to be connected to
perform this procedure. If the VIN number is still not transmitted, refer to the Troubleshooting Section of this
Service Information.
10. If the test call verified the correct VIN, then complete the attached TCU Registration Form with the ESN number
and fax to 201 307 4452.
11. Check the functionality of the telephone.
PORTABLE PHONE CODING PROCEDURE FOR ALL E46 (3 SERIES) FROM 9/03, E83 (X3) FROM 9/03, E85 (Z4) FROM 10/03,
AND E53 (X5) FROM 10/03, EQUIPPED WITH THE PREMIUM PACKAGE (ZPP) OR BMW ASSIST (SA639) ALL UP TO 3/05
PRODUCTION
E46 (3 Series)
1. Select "3. ZCS/FA Coding".
2. Select "7. E46 3 Series".
3. Select "2 Retrofit".
4. Select "Telephone Professional US".
5. "The TCU is recoded and the vehicle order in KOMBI automatically changed." Is displayed. Continue to next screen.
6. "TCU Start automatic coding?" answer "YES" and continue.
7. Once the coding is completed, print the new vehicle order and ensure that in the "HO-Wort:' section "TEPR" is
present.
8. Turn ignition off for 10 seconds and install handset and check functionality of phone.
E53 (X5)
1. Select "3 ZCS/FA Coding".
2. Select "8 E53 Series".
3. Select "2 Retrofit".
4. Select "26 Telephone professional US"
5. Continue until coding is complete and new ZCS code is displayed on screen.
6. In some instances an error message "Not possible to retrofit TCU according to coding code" is displayed. If this is
the case then manually change the ZCS code according to the attached chart.
7. 2005 MY vehicles have Bluetooth activated from the factory. In order to retrofit a CPT9000 (V60) telephone
and deactivate Bluetooth the ZCS code must be changed according to the attached chart for 2005 Model Year.
8. Turn ignition off for 10 seconds.
9. Install handset and check functionality of the phone.
E83 (X3), E85 (Z4)
1. Using DISplus or the SSS (Software Service Station) start CIP 12.0 or higher and select the "Load Software" button.
2. Answer "No" to "Have control modules been replaced?"
3. Select "Retrofits".
(223 pages)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals