Bmw M6 Convertible 2010 User Manual download pdf (Page 209)

Mobility

207

Reference At a glanceControlsDriving tipsCommunications NavigationEntertainment

Switch on the device and allow to run for

approx. 3 minutes to fill wheel with sealant.

It is not important what inflation pressure

the tire has after filling.

9. Switch off device.

10. Remove connecting hose from connection

of sealant bottle and tire valve.

Stow the M Mobility System in the vehicle

again.

Distributing sealant

Immediately drive approx. 2 miles/3 km so that

sealant is evenly distributed in tire.

Do not exceed a maximum speed of

35 mph/60 km/h. Do not drop below

12 mph/20 km/h if possible.<

Producing tire inflation pressure

1. After approx. 2 miles/3 km, stop at suitable

location.

2. Screw compressor hose 9 directly onto tire

valve.

3. Insert connector 3 in lighter socket in vehi-

cle interior.

4. Correct tire inflation pressure to 29 psi/

200 kPa. With the ignition switched on:

> Increase inflation pressure: switch on

device, position I. To check currently set

inflation pressure, briefly switch off

device.

Do not allow compressor to run

longer than 10 minutes, otherwise

the device will overheat and may be dam-

aged.<

> Reduce inflation pressure: press

button 8 or turn screw 8 on pressure

gauge.

If the inflation pressure is not held, drive

the vehicle again, refer to Distributing

sealant. Then repeat steps 1 to 4 once.

Using the M Mobility System can be ineffective

with tire damage from a size of approx. 0.16 in/

4 mm. Please contact the nearest BMW center,

refer to page 213, or a workshop that works

according to BMW repair procedures with cor-

respondingly trained personnel if the tire can-

not be made ready for driving with the

M Mobility System.<

The tire inflation pressure must be at least

29 psi/200 kPa. Otherwise do not con-

tinue driving.<

Continue driving

Do not exceed the permissible maximum

speed of 50 mph/80 km/h, otherwise

accidents can occur.<

Reinitialize the Flat Tire Monitor.

For details, refer to page 80.

Have the defective tire and the sealant bottle of

the M Mobility System replaced as soon as

possible.<

Changing wheels*

Safety precautions in the event of a flat

tire or wheel change: Park the vehicle as

far as possible from passing traffic and on solid

ground. Switch on the hazard warning flashers.

Apply the parking brake and shift into first gear

or reverse with the manual transmission, or

move the selector lever into a drive position with

the sequential transmission.

Have all vehicle occupants get out of the vehicle

and ensure that they remain outside the imme-

diate area in a safe place, such as behind a

guardrail.

If a warning triangle

or portable hazard warning

lamp

is required, set it up on the roadside at an

appropriate distance from the rear of the vehi-

cle. Comply with all safety guidelines and regu-

lations.

Change the wheel only on a level, firm surface

which is not slippery. The vehicle or the jack

could slip to the side if you attempt to raise the

vehicle on a soft or slippery surface such as

snow, ice, tiles, etc.

Position the jack on a firm support surface.

Do not use a wooden block or similar object as a

support base for the jack, as this would prevent

it from extending to its full support height and

reduce its load-carrying capacity.

To avoid serious or fatal injury: never lie under

1 2 ... 204 205 206 207 208 209 210 211 212 213 214 ... 249 250

Bmw M6 Convertible 2010 User Manual Page 209

Comments to this Manuals

Bmw M6 Convertible 2010 User Manual Page 209

Comments to this Manuals

Related products and manuals for Cars Bmw M6 Convertible 2010